Yo,
Although I don't like to remove smog eq.
Removal; "...What you need to do is electrically plug in the TAB and TAD solenoids but remove the vacuum lines, then all the air injection plumbing and valves can be removed and the heads plugged. The EGR is a seperate system from the Thermactor and the computer treats it very differently, it also helps increase milage and power so it's a good idea to keep it anyway. If you have the DPFE system there is no way to bypass it without the computer knowing and throwing a code so you may as well keep it intact. you'll get codes if you remove the solenoids, the easiest way to avoid this is to just leave them plugged in. The TAB and TAD you could fake out pretty easy, but even the old EGR system can't be faked because the computer both commands valve movement and watches for feedback to confirm it happened, so a dummy resistor won't cut it. by Paul
.....
These parts are commonly used & available via google searches:
Eliminator Overview, EGR Block Off Plate, EVR, CANP, TAB & TAD Actuator Eliminator Resistor & Parts List & pics; need one 75 ohm 3watt Resistor for each item removed, EVR, CANP, TAB & TAD solenoids
Some pics of each, but company is out of business:
http://api.viglink.com/api/click?format=go&jsonp=vglnk_146746810387314&key=6ed47b392b9edfe394b9e89b72717104&libId=iq58k6y601000bgv000MAcbg8dzms95tg&loc=http%3A%2F%2Fwww.fullsizebronco.com%2Fforum%2F21-noobie-bronco-tech-questions-flame-free-zone%2F417409-egr-smog-deletes.html&v=1&out=http%3A%2F%2Fweb.archive.org%2Fweb%2F20120820002649%2Fhttp%3A%2F%2Fwww.rjminjectiontech.com%2Fcollections%2Fegr-eliminators&title=EGR%20and%20Smog%20Deletes%20-%20Ford%20Bronco%20Forum&txt=RJM%20Injection%20Tech%20%3F%20EGR%20Eliminators
Tad and tab resistors see
and a neat mod by jrichker; "...Put the resistor inside the heat shrink tubing and crimp the connectors on. I would choose the Ford pin connectors since they should plug in the TAB & TAD wiring. That way you haven't modified the wiring so it is easy to re-install the TAB & TAD solenoids if emissions testing comes to your area. 18 gauge crimp on taps Catalog #: 64-3053
Two flat pin connectors.
One 82 ohm, 3 watt resistor. (diff Ford/..)
One piece 3/8" heat sink tubing 2" long.
Two pieces 3/16" heat shrink tubing 1 1/2" long.
Solder the pins onto the resistor leads using electrical solder.
Slide the 3/8" heat shrink tubing over the resistor.
Slide the two pieces of 3/16" heat shrink tubing over the two wires, leaving the flat part of the pins uncovered
It helps to have the resistor leads straight and not bent as shown in the first picture when you apply heat to the heat shrink tubing. That way, the tubing shrinks more evenly.
Finally, apply heat to shrink all the tubing uniformly
Bend the leads to fit the spacing on the female TAB & TAD connector sockets.
Push the connector pins of the completed resistor assembly into the empty female TAD or TAD connector sockets on the wiring harness. The resistor assemblies replace the missing solenoids: one resistor assembly per solenoid socket..."
read more and see many pics
http://api.viglink.com/api/click?format=go&jsonp=vglnk_146746832470313&key=6ed47b392b9edfe394b9e89b72717104&libId=iq58qa3h01000bgv000MA1tuw5nd0&loc=http%3A%2F%2Fwww.fullsizebronco.com%2Fforum%2F21-noobie-bronco-tech-questions-flame-free-zone%2F170822-wiring-resistors-tab-tad-how.html&v=1&out=http%3A%2F%2Fwww.stangnet.com%2Fmustang-forums%2F790379-finally-learned-how-read-codes.html&ref=http%3A%2F%2Fwww.fullsizebronco.com%2Fforum%2F21-noobie-bronco-tech-questions-flame-free-zone%2F417409-egr-smog-deletes.html&title=wiring%20resistors%20in%20for%20TAB%2FTAD%2C%20how%20to%3F%20-%20Ford%20Bronco%20Forum&txt=http%3A%2F%2Fwww.stangnet.com%2Fmustang-foru...ead-codes.html
Smog Pump:
Removal, Belt in an 88 5.0; "...I tried an 89.5" first, 2 inches shorter than stock and it was too long. So I went back hoping for something about 88 or so and all they had was a 87.5. It was a bit short and a royal pita to put on but it is running fine. A lil tight but it should hold till I get an 88.2 which they can order..."
Source: by fright88
Removal, Belt Part Number 882K6 in an 88 5.0
Source: by Barbaric35
I have no info for your 86 351 belt.
And having issues with this Tablet,
So see
http://broncozone.com/topic/25185-bronco-project-mechanical-issues/
my post #18
...