Search results

Hi, I'm in the process of rebuilding a '95 5.8L.I had a reputable machine shop assemble the long block and told them I wanted a noisy set of timing gears, now that the engine is done, gear set installed, I'm reading some stuff that says timing gears are not intended for running a roller...

I'm rebuilding a 5.8L out of a 1995 E150 for my 73 bronco, I would like to put the bronco script valve covers on it but they say that they will not work on efi engines. I am going to be running a set of gt40 heads and an explorer/cobra upper on a cast iron marine 5.8L lower. When you search...

I found a c6 and case out of a 87 bronco on the cheap, and was wondering if anybody knows if it would swap into a 73 without too much trouble,  by too much I mean driveshaft mods, and somewhere I read about a body lift for a c6.  any info would be great thanks!

has anyone changed thier water pump pully to increase speed and flow for mild temp problems. my bronc dont overheat in normal everyday driving but it tends to warm up when idleing on the trails. the radiator is free and clear, the stat is working, timing is good. i was just curious about...

anybody ever find anything to replace the back seat with? modifying is ok but ive looked the boneyards high and low for like a back seat or third row out of a mini van or something but havent been able to find anything narrow enough.

hello, i have been searching and cant seem to find anything pictures or otherwise about the larger 23 gal main fuel tanks. for the most part they all look like they are made by the same person/company, except for these new ones with the piece of uni-strut welded to the side for mounting. so...

a while back i seen a article on power and gas milage upgrades, im pretty sure it was a late 80's early 90's centurion bronco with f 350 chasis and 460 efi they did all kinds of things from exhaust to insulating the airbox. they got pretty impressive #'s and had it all compaired on charts and...

looking for other ideas. :wacko: while driving along between 1K and 2K RPM my lights go dim, heater slows down, wipers slow down, and alt. gauge steadies at zero all at once just like i flipped a switch. then... a few seconds later, just like a switch everything comes back on. replaced...

i was changing the oil in my transfer case and bought some red line 75-90 synthetic gear oil. what i didnt notice until i was ready to put it in and read the back of the bottle is that it says it might not be recomended for use in some manual trannies because it might cause gear clash. has...

hi, i was wondering if you were able to swap fuel injection onto a 351 w / 5.8L as easy as doing it on a 302 / 5.0L. do you have to change the heads or just the intake. i have a 1981 f250 with a fresh 351 w and want to put efi on it. i did the conversion on my 67 bronco with a 302 and it...

hello, i recently seen an article in a bronco driver magazine that told of a heater upgrade for 66 to 77 broncos using a blower motor and squirl cage from a 79 chevy truck. the article had a picture of the stock bronco cage next to the chevy one and the chevy cage is quite a bit bigger. well...

hi, i recently picked up a set of gt- 40p heads, upper and lower intake, throttle body, ect. from a 1996 explorer. i have a couple of questions about these parts vs. what i have now, any info would be great ! first,.... will the 1996 heads bolt onto a 1970 302 block with no mods? second,.... are...

hi, i recently picked up a set of gt- 40p heads, upper and lower intake, throttle body, ect. from a 1996 explorer. i have a couple of questions about these parts vs. what i have now, any info would be great ! first,.... will the 1996 heads bolt onto a 1970 302 block with no mods? second...

hello, a while ago i swapped out the dana 30 in my '67 for a '73 or '74 dana 44. when i did i swapped the drums for disks from a full size f150. everything from the ball joints out, all new ball joints, u joints, wheel bearings, steering linkage ect... everything is tight and good but with...

hi, i have a '67 that originaly had vacume wipers. someone has changed them to two individual motors, and now i have bought the newer style wiper setup with one motor and linkage. does anyone know where to drill the holes in the frame or can you change the length of the linkage to make it work...

hi, i'm looking for a new process 435 4 speed to a new process 205 x-fer case adaptor housing. if anyone knows where i can get one, (web site or phone #)that would be very helpful! and if anyone knows from experience if you have to lengthen/shorten the drivelines when changing from auto to man...