Search results

Well after tons of work over the last 6 months the engine is done. It is 351W in a 93. Should I replace it with the same, a crate, anything else recommended or suggestions? I may try and do it all myself but if that ends up being a time commitment I don't have then I will purchase it and have...

Was driving a few days ago and it started sounding different in the engine like it was backing off of normal noise. Pulled in to a place, checked things out, got back in and did not start and the wonderful engine check light came on. Turns over, fuel pump engages but won't fire. Had a broken...

Need to replace the ignition coil bracket on my 93 with the 351W. One of the sides broke off where it attaches and it is just rattling around and the coil crapped out. Ford says the part number is F4UZ12043AA but they don't sell it anymore. Anyone have any ideas? I know it is the same bracket...

My 93 Bronco has a Superlift Superunner 6" Suspension kit with 2 superlift shocks on each side with 6" coils and running 35's on it. Trying to do some research on Caster, Camber and Toe because it rides pretty rough and I feel every crack. Any ideas where to look and see what the settings for...

On my 93 Eddie Bauer it has a set of two bolts in all four corners on the top of the topper. Are these for mounting a roof rack, installing hooks to hoist the topper off, or something completely different. They don't seem to attach to anything on the inside. Thanks for your help.

Thank you Al. You have been very helpful and enough stuff to look through that will keep me busy for weeks. As you can see by my profile picture it is lifted a bunch and at least 4" if not more. Those are 35s on the rims. I will take the info from one of your links and find the angle. Since my...

Thank you everyone. New transmission fluid, filter, and gasket did the trick. Runs like new! A couple things concerning the threads. Rear differential - Not sure if is a Dana 44 or a 8.8. Gear ratio is 4.1. What was recommended above was 2.75 quarts. I put that in and that did not even come...

All good stuff guys. I just did mine in my 93 a month ago. It is time consuming but I agree it is a 5 on the 1-10 scale and that was the first time I did it. Like others said keep your bolts organized. I also took pictures of each area before I took something off so I could reference that when I...

Did the gear check once I got it lifted up. Axle rotated a little over 4 times. Limited slip chart you showed has a H3 4.11 and a H5 4.10 which would be close. Anyway to figure out which one of the two besides what I just did?

Just a couple things that I cannot find on your replies and cannot find it anywhere. Torque specs for the  bolts in the oil pan, transmission pan, and the rear diff cover. Also they make a rear diff cover gasket but should I just make one using RTV. Which one would be better.

Thank you for the help over the last month with my new 93 Bronco. I have had it just over a month and have done a lot with the plugs, wires, rotor and cap, tailgate issues, etc. I am ready to change all the fluids. Cannot find what exactly is the correct choice for everything. Haynes does not...

A light swtich. That makes sense. The window will only go down from the dash switch. It won't go up. The key switch does not work. Going to take off the left tail light today and see if something is cut in the harness that goes through that area. With the window out I can see that there is just...

First thank you to everyone and Al for your help. I am a 2 month old Bronco owner so some of this stuff is all new. My rear window on my 93. It does not work and the side windows do work. Here is where I sound a little stupid and I have tried to look through posts and other stuff to find out...

BTW, It is a 351W. While I am asking specs say plug head spacing is 44. Yes?

Replacing the distributor, rotor, plugs, and wires on my 93. It is a MSD Rotor and cap. Did not check and mark which way the rotor was pointing when I took it off. Anyone have an idea which way I should point it because I am reading many different opinions googling it. Thank you

Thank you, I posted a few pics of the engine area.

Thanks guys, I agree if I had to do it I would not add all that but could not pass up the deal I got on it so bought it. It is the first vehicle I have own that has headers and a super charger so this is all new to me. I understand what you are saying by the wires close to the headers. They look...

Got a 93 with 351W. Need to switch out plugs and wires. Recommendations? Running Bassani Short headers now but need to replace them because one is cracked. Stick with the same thing?  It has a super charger, Edelbrock Cylinder heads, Edelbrock 3881 Manifolds, Speed-Pro Power forged Pistons...