Search results

I just finished doing the same thing to my 95 EB and it makes a world of difference. The steering is nice and tight

If you replaced any of the break lights with LEDs the cruise wont work. It is looking for the resistance of the bulbs. Also there was a recall on the cruise unit some time ago

If you installed LED break light It will stop the cruise from working. The cruise control works off the resistance in the break light circuit

Google PSOM { 'Programmable Speedometer Odometer Module } Its on the back of the instrument cluster and after time the solder breaks down causing bad signals to the ECM. My E4OD had the same problem and after a lot of trouble shooting I called a speedo repair shop in Florida and they fixed it.

I had a similar problem. I checked the ohms reading coming from the sender at the connector closest to the tank then I filled the tank and checked again, there was no change so I had to change the pump/sender unit. This can be done without dropping the tank by cutting the floor over the sender...

My 1995 had the same symptoms. I sent my cluster to DNA Speedomiter Inc. in Tampa. The cost was $175 back in 2011and I've had no problems since, There are other repire services on the internet. Google P.S.O.M. repair

My Over Drive light would flash and the transmission would shift hard { 5.0 E4OD }. It turned out to be the P.S.O.M. { programmable speedometer odometer modual } I shipped the instrument cluster to a speed committer shop in Fla. and they fixed it. Google PSOM.

My gauge was in actuate so I checked the ohms reading and filled the tank and it still shower empty { 10 ohms= full, 70 ohms=empty} so i changed the unit, the float had a hole and was full of gas. here is a link for removing the sending unit with out dropping the tank...

Check the MAF on the air intake. If it isn't functioning or in place the engine wont run

If you replaced any break light bulbs with LED replacements then the cruise wont work. It need the resistance in the standard bulbs.

My 95 would start then stall. On the second attempt it would start and run rough for a few seconds then smooth out as it warmed up. I replaced the original Idle Air Control valve and the problem went away

I just replaced the thermostat and radiator cap and there was no change. I purchased a myty vac preasure tester and the cap was good and the radiator pressure held in the 13psi area for an hour. With the gauge at zero I started the engine and it stayed at zero indicating the head gasket was...

I have a 1995 Ford Bronco 5.0 with 143000 miles. Recently I added a temperature gauge so there are two sending units, one for the gauge and the other for the dash unit, I live in New England so the other day when the outside temp was 30 degrees the truck would not warm up to more than 170. I...

Search the internet for P.S.O.M. Programmable speedometer odometer module. .Its part of the instrument cluster. I sent mine to a shop in Fla. and it has been fine since

My top is Tan. I mask off the paint and wipe it down with laquer thinner and a scotch bright pad to clean it then wipe on clear acrylic { the type used on linoleum flooring} using a clean cotton cloth. The acrylic needs to dry till its not tacky.

I called Jeff's and he get his replacement parts from the same Taiwan distributors . Its frustrating because if things don't line up right you have to pay the return shipping. I was trying to replace the two front fender. I think you would have good luck with Jeff's or LCM for a tailgate shell...

I found this site after I got the truck repaired. I haven't used it yet but it sounds promising https://www.hollanderparts.com/

I have a 1995 Bronco that needed two front fenders. All after market parts come form Taiwan no mater who you buy from and the die they are using is worn out. I tried two different vendors and spoke to many more, they did not fit. I cant speak for the smaller panels but the larger stuff was no...

I had a bad leak that I thouht was coming from the rear main seal but turned out to be the original oil pan gasket was no good. I replace it with a Fel-pro one piece gasket and no more leaks. The cross member and exhaust cross over pipe prevents you from removing the pan but you can drop it...